Add files via upload

templates/command_templates/cisco/interface_config.py

@@ -0,0 +1,121 @@
+"""
+思科设备接口配置模板
+支持配置接口IP、状态、带宽、描述等操作
+"""
+
+def configure_interface_ip(interface: str, ip_address: str, subnet_mask: str) -> str:
+    """
+    配置接口IP地址
+    
+    Args:
+        interface: 接口名称，如 GigabitEthernet0/1
+        ip_address: IP地址
+        subnet_mask: 子网掩码
+    
+    Returns:
+        配置命令字符串
+    """
+    commands = [
+        "configure terminal",
+        f"interface {interface}",
+        f"ip address {ip_address} {subnet_mask}",
+        "no shutdown",
+        "exit",
+        "end"
+    ]
+    return "\n".join(commands)
+
+def configure_interface_state(interface: str, state: str = "up") -> str:
+    """
+    配置接口状态
+    
+    Args:
+        interface: 接口名称，如 GigabitEthernet0/1
+        state: 接口状态，up或down
+    
+    Returns:
+        配置命令字符串
+    """
+    commands = [
+        "configure terminal",
+        f"interface {interface}"
+    ]
+    
+    if state.lower() == "up":
+        commands.append("no shutdown")
+    elif state.lower() == "down":
+        commands.append("shutdown")
+        
+    commands.append("exit")
+    commands.append("end")
+    return "\n".join(commands)
+
+def configure_interface_description(interface: str, description: str) -> str:
+    """
+    配置接口描述
+    
+    Args:
+        interface: 接口名称，如 GigabitEthernet0/1
+        description: 接口描述
+    
+    Returns:
+        配置命令字符串
+    """
+    commands = [
+        "configure terminal",
+        f"interface {interface}",
+        f"description {description}",
+        "exit",
+        "end"
+    ]
+    return "\n".join(commands)
+
+def configure_interface_bandwidth(interface: str, bandwidth: str) -> str:
+    """
+    配置接口带宽
+    
+    Args:
+        interface: 接口名称，如 GigabitEthernet0/1
+        bandwidth: 带宽，单位kbps
+    
+    Returns:
+        配置命令字符串
+    """
+    commands = [
+        "configure terminal",
+        f"interface {interface}",
+        f"bandwidth {bandwidth}",
+        "exit",
+        "end"
+    ]
+    return "\n".join(commands)
+
+def show_interface(interface: str = None) -> str:
+    """
+    显示接口信息
+    
+    Args:
+        interface: 接口名称，如GigabitEthernet0/1，为None时显示所有接口
+    
+    Returns:
+        显示命令字符串
+    """
+    if interface:
+        return f"show interface {interface}"
+    else:
+        return "show interface"
+
+def show_ip_interface(interface: str = None) -> str:
+    """
+    显示接口IP信息
+    
+    Args:
+        interface: 接口名称，如GigabitEthernet0/1，为None时显示所有接口
+    
+    Returns:
+        显示命令字符串
+    """
+    if interface:
+        return f"show ip interface {interface}"
+    else:
+        return "show ip interface brief" 

templates/command_templates/cisco/topology_discovery.py

@@ -0,0 +1,88 @@
+"""
+思科设备的拓扑发现命令模板
+支持CDP和LLDP协议的邻居发现
+"""
+
+def get_cdp_neighbors():
+    """获取CDP邻居列表"""
+    return "show cdp neighbors"
+
+def get_cdp_neighbors_detail():
+    """获取CDP邻居详细信息"""
+    return "show cdp neighbors detail"
+
+def get_lldp_neighbors():
+    """获取LLDP邻居列表"""
+    return "show lldp neighbors"
+
+def get_lldp_neighbors_detail():
+    """获取LLDP邻居详细信息"""
+    return "show lldp neighbors detail"
+
+def enable_cdp():
+    """全局启用CDP"""
+    return "cdp run"
+
+def enable_cdp_interface(interface: str):
+    """在指定接口启用CDP"""
+    return f"""interface {interface}
+cdp enable
+exit"""
+
+def enable_lldp():
+    """全局启用LLDP"""
+    return """lldp run"""
+
+def enable_lldp_interface(interface: str):
+    """在指定接口启用LLDP"""
+    return f"""interface {interface}
+lldp transmit
+lldp receive
+exit"""
+
+def get_interface_brief():
+    """获取接口简要信息"""
+    return "show ip interface brief"
+
+def get_interface_status():
+    """获取接口状态"""
+    return "show interface status"
+
+def get_interface_description():
+    """获取接口描述"""
+    return "show interface description"
+
+def get_cdp_interface(interface: str):
+    """获取指定接口的CDP信息"""
+    return f"show cdp interface {interface}"
+
+def get_lldp_interface(interface: str):
+    """获取指定接口的LLDP信息"""
+    return f"show lldp interface {interface}"
+
+def get_cdp_entry(device_name: str):
+    """获取特定设备的CDP条目"""
+    return f"show cdp entry {device_name}"
+
+def get_vlan_brief():
+    """获取VLAN简要信息（用于拓扑分析）"""
+    return "show vlan brief"
+
+def get_spanning_tree():
+    """获取生成树信息（用于拓扑分析）"""
+    return "show spanning-tree"
+
+def get_mac_address_table():
+    """获取MAC地址表（用于二层拓扑分析）"""
+    return "show mac address-table"
+
+def discover_full_topology():
+    """发现完整拓扑的命令序列"""
+    commands = [
+        "show cdp neighbors detail",
+        "show lldp neighbors detail", 
+        "show ip interface brief",
+        "show interface description",
+        "show vlan brief"
+    ]
+    return commands 

templates/command_templates/cisco/vlan_config.py

@@ -0,0 +1,94 @@
+"""
+思科设备VLAN配置模板
+支持创建VLAN、配置VLAN名称、将接口添加到VLAN等操作
+"""
+
+def create_vlan(vlan_id: str, vlan_name: str = None) -> str:
+    """
+    创建VLAN
+    
+    Args:
+        vlan_id: VLAN ID
+        vlan_name: VLAN名称(可选)
+    
+    Returns:
+        配置命令字符串
+    """
+    commands = [
+        "configure terminal",
+        f"vlan {vlan_id}"
+    ]
+    
+    if vlan_name:
+        commands.append(f"name {vlan_name}")
+    
+    commands.append("exit")
+    commands.append("end")
+    return "\n".join(commands)
+
+def add_interface_to_vlan(interface: str, vlan_id: str, mode: str = "access") -> str:
+    """
+    将接口添加到VLAN
+    
+    Args:
+        interface: 接口名称，如 GigabitEthernet0/1
+        vlan_id: VLAN ID
+        mode: 接口模式，access或trunk
+    
+    Returns:
+        配置命令字符串
+    """
+    commands = [
+        "configure terminal",
+        f"interface {interface}",
+        "switchport"
+    ]
+    
+    if mode.lower() == "access":
+        commands.append("switchport mode access")
+        commands.append(f"switchport access vlan {vlan_id}")
+    elif mode.lower() == "trunk":
+        commands.append("switchport mode trunk")
+        commands.append(f"switchport trunk allowed vlan add {vlan_id}")
+    
+    commands.append("exit")
+    commands.append("end")
+    return "\n".join(commands)
+
+def delete_vlan(vlan_id: str) -> str:
+    """
+    删除VLAN
+    
+    Args:
+        vlan_id: VLAN ID
+    
+    Returns:
+        配置命令字符串
+    """
+    commands = [
+        "configure terminal",
+        f"no vlan {vlan_id}",
+        "end"
+    ]
+    return "\n".join(commands)
+
+def show_vlan() -> str:
+    """
+    显示VLAN信息
+    
+    Returns:
+        显示命令字符串
+    """
+    return "show vlan brief"
+
+def show_vlan_detail(vlan_id: str) -> str:
+    """
+    显示特定VLAN的详细信息
+    
+    Args:
+        vlan_id: VLAN ID
+    
+    Returns:
+        显示命令字符串
+    """
+    return f"show vlan id {vlan_id}"